Item number RPH20 Rite-Bite Custom moldable mouthpiece Experience the Difference and Feel that a Custom Rite-Bite mouthpiece makes on your very next dive! Prior to the use of this product, you should determine the safety, suitability and fitness of the product for it’s intended use.  As Trident, the manufacturer, or the seller assume no liability arising out of the use or misuse of this product. Those suffering from diseases or inflammation of the teeth or gums, wearers of dentures or are wearers of crowns or have other dental issues should consult wiht their dentist before using or customizing a Rite-Bite mouthpiece. RECOMMENDATIONS AND WARNINGS The Rite-Bite mouthpiece can be reshaped several times. For this reason, always keep the customization devices. Any excess material that may extrude after customization, can be removed using scissors.     Important: Never use Rite-Bite with the customization devices inserted. Keep your Rite-Bite mouthpiece away from heat sources and direct sunlight as it could deform. ITEMS INCLUDED WITH THE RITE-BITE MOUTHPIECE FOR USE DURING THE CUSTOMIZATION PROCESS Device A  (THE HOLDER TAB) This simplifies the customization of the mouthpiece and prevents any deformation of the dispenser cavity that slips over the SCUBA regulator. Device B (2 PIECES) (LATERAL STOPS) These are inserted in the mouthpiece sides to maintain the optimum thickness of material between the upper and lower teeth during customization. They are to be removed after the customization process is complete, and kept for future custimization processes. "UP" Symbol The letters UP that are raised on the side of the mouthpiece that helps to describe the correct position of the mouthpiece in your mouth: If you have an overbite: The “UP” position of the mouthpiece will be upward in your mouth during the customization process. (and on your SCUBA regulator after the customization process) If you have an underbite: The “UP” position of the mouthpiece will be downward in your mouth during the customization process. (and on your SCUBA regulator after the customization process) BEFORE BEGINNING THE CUSTOMIZATION PROCESS ASSEMBLE THE FOLLOWING MATERIALS: 3-quart saucepan (or a pan at least 6 inch diameter and 4 inches deep) Sharp pair of scissors for trimming the mouthpiece end tips Mirror for seeing a centered allignment of the mouthpiece in your mouth during the customization process Container of cold water large enough to cool the complete mouthpiece after customization DETERMINING THE PROPER POSITIONING FOR YOUR JAW: Unlike conventional mouthpieces, the Rite-Bite mouthpiece must fit your mouth and jaw configuration precisely. Therefore, it has to be positioned in your mouth properly Most people have an overbite: A dental condition where your front teeth extend over your lower teeth while biting down normally If you have an overbite: The “UP” position of the mouthpiece will be upward in your mouth during the customization process. (and on your SCUBA regulator after the customization process) If you have an underbite: The “UP” position of the mouthpiece will be downward in your mouth during the customization process. (and on your SCUBA regulator after the customization process) THE POSITIONING IS VERY IMPORTANT FOR MAXIMUM COMFORT AND EFFECTIVENESS PRIOR TO BEGINING THE CUSTOMIZATION OF THE MOUTHPIECE Make sure that devices A and B are inserted correctly.   Know whether the “UP” position on the mouthpiece will be upward or downward in your mouth while customizing. (the UP symbol facing the upper teeth or lower teeth)(determined by you having an over or under bite) Practice inserting the mouthpiece into your mouth prior to heating to build confidence for the next steps in the customization procedure. AT THIS POINT THE UNIT HAS NOT BEEN MOLDED AND WILL NOT YET FEEL COMFORTABLE. You will note that, unlike conventional mouthpieces, that the Rite-Bite mouthpiece extends back to include all of your teeth. If the mouthpiece bite wing tips touch the back of your mouth beyond the last teeth, use scissors to trim off a small portion of each bite wing tip. Note: Only off 1/8th inch of the tips at a time! Retry the mouthpiece in your mouth before trimming more. TRIM ONLY ENOUGH TO CLEAR THE BACK OF YOUR MOUTH BEGINNING THE CUSTOMIZATION PROCESS In a three-quart saucepan (or a pan at least 4 inches diameter and deep enough to hold 4 inches of water) fill with water to at least 4 inch depth. Bring water to a vigorous and rolling boil. Remove from heat and let water sit a few moments until the bubbling stops. Holding the mouthpiece with Device A with the bite tips pointed down, and with Devices B inserted: Submerge the bite portion into the hot water up to the top of the bite piece portion area of the mouthpiece. DO NOT PUT THE REGULATOR END INTO THE WATER DO NOT IMMERSE THE ENTIRE MOUTHPIECE! Hold the mouthpiece in this immersed position for 20 seconds DO NOT HEAT THE MOUTHPIECE BEYOND THE 20 SECONDS OR IMMERSE BEYOND THE LINE INDICATED AS DAMAGE TO THE MOUTHPIECE MAY OCCUR Remove from the hot water and shake off all water after removing it. DO NOT PLACE THE MOUTHPIECE IN YOUR MOUTH IF HOT WATER REMAINS ON IT. Immediately place the mouthpiece in your mouth with the word “UP” properly positioned for your over or under bite. and perform the following steps, working in front of a mirror to be sure the mouthpiece is centered under your nose: Know the pre-determined “UP” position of the mouthpiece Place the mouthpiece in the mouth immediately after shaking off the excess hot water. Clench the teeth and close the mouth. Bite down firmly for a few seconds to obtain ideal adhesion around the teeth BUT DO NOT ATTEMPT TO BITE THROUGH THE MOUTHPIECE. While setting your teeth, press the inner portion of the bite wings against the inside of your teeth with your tongue At the same time, press the outer edges of the bite wings against your teeth and gums by pressing your fingers firmly against your cheeks. Do this for about 2 minutes, then remove the Rite-Bite mouthpiece and place it in the container of cold water for at least 3 minutes. Remove the mouthpiece from the water and remove the customization devices A and B. The mouthpiece is now custom-molded to your teeth and gums. Insert the mouthpiece into your mouth again and check for a comfortable fit. Your customized Rite-Bite Mouthpiece is now ready to be installed on your regulator, using the plastic tie strap provided. Test the fit of your mouthpiece to the regulator for a proper fit. IF YOU HAVE ANY DOUBT ABOUT THE PROPER FITTING BETWEEN YOUR REGULATOR AND THE MOUTHPIECE BRING IT TO YOUR LOCAL DIVE STORE FOR INSPECTION Prior to the use of this product, you should determine the safety, suitability and fitness of the product for it’s intended use. As Trident, the manufacturer, or the seller assume no liability arising out of the use or misuse of this product. THE RITE-BITE MOUTHPIECE IS REMOLDABLE! If you are not entirely satisfied with the initial fit, simply repeat the customization process, making sure the unit is at room temperature before starting the customization process again. Repeat as often as necessary to achieve a comfortable fit. DO NOT REMOLD IMMEDIATELY FOLLOWING ANY PREVIOUS MOLDING WITHOUT FIRST THOROUGHLY COOLING OFF THE  MOUTHPIECE WARRANTY The Rite-Bite mouthpiece is warranted to be free from defects in workmanship and materials when packaged and shipped. Liability under this warranty is limited to the cost of replacement of the Rite-Bite Custom Mouthpiece sold to the original purchaser. No other warranties related to the use of our product are expressed or implied by Trident Diving Equipment.